Post by jenks on Nov 24, 2008 23:16:39 GMT -5
33 x 12.50 boggers mounted on Mickey Thompson classic II rims $800
tires $550 / rims $250 will separate APPROXIMATELY 75% to 80% TREAD
33 x 12.50 TSL's swampers mounted white spoke rims $450
tires $400 / Rims $50 will separate 68%,75%,80%,80%
Dana 44's (package) $200
1- axle complete 6 lug don't know the gears would guess 3.73
1- housing off of 3/4 ton with center section 3.73
1- axle off of 3/4 ton missing short side axle and stub, was told carrier gears were junk, missing lockouts, but I have some spares to replace.
2- large bearing spindles and maybe a few others I think I also have some spare 8 lug hubs for big bearing, not for sure.
1- long side axle and stub
1 -short side axle, stub attatched but has wear where meets the back of spindle (junk in my eyes)
Dana 44 front and 12 bolt rear out of 1/2 ton chevy. Richmond 4.56 gears, Detroit truetracs front and rear. Gears and seals 2 years old. 6 Lug with lockouts. $900
TH 350 with NP 203
Trans rebuilt 2 years ago. Has B&M clutches and steels as well has transpack (hard shift) Manual valve body and will engine brake. Has leak, I believe just pan gasket. NP 203 has part time kit in it. Also comes with ORD twin stick for NP203, Allows 2 wheel high / low and 4 wheel High / Low $300
BBM Six pack rods $100
BBM OEM cast heads bare / ported $50
warn lockouts for dana 60 NIB $100
Dana 60 rear ff out of a 76 dodge. 4.10 gears, open, 30 spline axles. ($150)
2- 30 spline lockrights NIB for dana 60 ($300 each)
Used gearset 4.10, came out of dodge 60 front. Comes with open carrier, I removed the bearings off of the carrier. ($50)
Dual plane oval port Wieand Intake for BBC ($75)
Holley 750 , 4bl with vac secondaries and dual fuel line (Needs Rebuilt) ($50)
BBC heads, Closed chamber 98 cc, casting number 3872702, need tore down and cleaned. ($200)
BBC stock rods come with .030 over flat top pistons for 454 ($50)
cast crank for 454 ($50)
QFT 650 double pumper carburetor that has been modified and the choke horn milled off. It flows around 735 cfm. It is about 6 months old was on my 350 engine which I am changing to a warmed over big block and is no longer needed. Asking $250.
dodge 60's front and rear. welded / detroit 5.38 gears $1200 for the pair.
6" arched springs for dodge as well
815-878-2120
Located in Granville, IL
later
jenks
tires $550 / rims $250 will separate APPROXIMATELY 75% to 80% TREAD
33 x 12.50 TSL's swampers mounted white spoke rims $450
tires $400 / Rims $50 will separate 68%,75%,80%,80%
Dana 44's (package) $200
1- axle complete 6 lug don't know the gears would guess 3.73
1- housing off of 3/4 ton with center section 3.73
1- axle off of 3/4 ton missing short side axle and stub, was told carrier gears were junk, missing lockouts, but I have some spares to replace.
2- large bearing spindles and maybe a few others I think I also have some spare 8 lug hubs for big bearing, not for sure.
1- long side axle and stub
1 -short side axle, stub attatched but has wear where meets the back of spindle (junk in my eyes)
Dana 44 front and 12 bolt rear out of 1/2 ton chevy. Richmond 4.56 gears, Detroit truetracs front and rear. Gears and seals 2 years old. 6 Lug with lockouts. $900
TH 350 with NP 203
Trans rebuilt 2 years ago. Has B&M clutches and steels as well has transpack (hard shift) Manual valve body and will engine brake. Has leak, I believe just pan gasket. NP 203 has part time kit in it. Also comes with ORD twin stick for NP203, Allows 2 wheel high / low and 4 wheel High / Low $300
BBM Six pack rods $100
BBM OEM cast heads bare / ported $50
warn lockouts for dana 60 NIB $100
Dana 60 rear ff out of a 76 dodge. 4.10 gears, open, 30 spline axles. ($150)
2- 30 spline lockrights NIB for dana 60 ($300 each)
Used gearset 4.10, came out of dodge 60 front. Comes with open carrier, I removed the bearings off of the carrier. ($50)
Dual plane oval port Wieand Intake for BBC ($75)
Holley 750 , 4bl with vac secondaries and dual fuel line (Needs Rebuilt) ($50)
BBC heads, Closed chamber 98 cc, casting number 3872702, need tore down and cleaned. ($200)
BBC stock rods come with .030 over flat top pistons for 454 ($50)
cast crank for 454 ($50)
QFT 650 double pumper carburetor that has been modified and the choke horn milled off. It flows around 735 cfm. It is about 6 months old was on my 350 engine which I am changing to a warmed over big block and is no longer needed. Asking $250.
dodge 60's front and rear. welded / detroit 5.38 gears $1200 for the pair.
6" arched springs for dodge as well
815-878-2120
Located in Granville, IL
later
jenks